Q See Baby Monitor QSW8209 User Guide

QSW8209  
LCD Baby Monitor  
Wireless Camera  
Visit Us on the Web at http://www.q-see.com  
Rev 092507  
 
1. Packing List  
1) 2.4GHz Wireless Camera  
2) 2.4GHz Wireless Receiver  
1
1
3) AV cable  
1
4) Power Adapter for camera  
5) Power Adapter for receiver  
1
1
Note: AA Batteries are not included  
2. Diagram  
 
3. Structure  
3-1. Layout of Camera  
3-2. Layout of Receiver  
 
4. Installation  
4-1. Setting up the Camera  
1. Setup the camera in the desired location  
2. Connect the camera to the adapter and then slide the power switch to the ON  
position  
Note:  
--This camera can also use dry batteries as a power source by loading 4 AA  
batteries into the battery compartment on the back of the camera with their  
polarities in the correct position.  
--The AC adapter will work instead of batteries after it is plugged in. If the  
 
camera is not going to be used for a long period of time, please unplug the  
adapter and remove the batteries.  
* The camera can run off of batteries for up to 5 hours (IR OFF)  
3. Rotate the rounded head of the camera to the desired angle for surveillance.  
4-1-1. Camera channel setup  
1. On the right side of the camera there is a channel selector switch marked  
CH1,CH2,CH3,CH4. If you have multiple cameras you would set each one on a  
different channel to avoid interference.  
 
2. Press the channel button on the receiver to select the same channel as the  
camera. When the channels match the picture will be displayed on the screen.  
4-1-3. Camera alarm setup  
1. The camera provides Motion Detection and Sound Detection. For each mode  
you can select 3 sensitivity levels: Low, Middle, High.  
Motion Alarm Setup:  
This alarm will detect movement in front of the camera. If you slide the alarm  
setting switch to the Motion position and select the Sensitivity level, the system  
enters motion alarm mode. When movement is detected, the alarm sounds until  
 
you press the Eliminate Alarm Button. Within 1 minute the motion alarm starts  
the next alarm circle.  
Sound Alarm Setup:  
This alarm will detect sound. If you slide the alarm setting switch to the Sound  
position, and select the Sensitivity level, the system enters sound alarm mode.  
When sound is detected, the alarm sounds until you press the Eliminate Alarm  
Button. When the alarm sounds the screen will also display the video unless you  
have pressed the Sleep button. Within 1 minute the sound alarm starts the next  
alarm circle.  
Off Alarm Setup  
This option turns off the alarm function. If you slide the alarm setting switch to  
the Off position. The alarm function is disabled.  
Note:  
If the camera is being powered by dry batteries and you plug in the power  
adapter, the alarm function will not work until you slide the power off switch  
to the ON position. The alarm function will then be reactivated.  
4-2. Setting up the Receiver  
1. Connect the receiver to the adapter and then slide the power switch to the ON  
position.  
 
Note:  
--This receiver can also use dry batteries as a power source by loading 4 AA  
batteries into the battery compartment at the back of the camera with their  
polarities in the correct position.  
--The AC adapter will work instead of batteries after it is plugged in. If the  
camera is not going to be used for a long period of time, please unplug the  
adapter and remove the batteries.  
* The camera can run off of batteries for up to 5 hours.  
2. Adjust the volume control to the desired level.  
 
3. Set the channel of the receiver to the same channel as the camera by pressing  
the channel button continuously, the pictures will display on the screen when the  
channels match.  
Note  
For clearer pictures you can connect the receiver to a monitor/TV with the  
included AV cable (yellow for video and red for audio).  
4-2-1. Operation of the Receiver  
1. Volume adjustment  
 
Slide “Volume Switch” to adjust the volume of the receiver.  
2. Channel selection  
Press “CH button” to select the desired channel.  
3. Channel Looping  
Hold the “CH button” for three seconds to enter the loop mode. All the available  
channels will be displayed one by one (default interval is 5 seconds).  
4. Sleep Mode  
Press the “Sleep Button” to shut down the LCD display and keep the voice  
function. Press the button again and recall the normal working mode. This can  
save energy.  
5. Eliminate Alarm button  
Press “Eliminate Alarm” button to stop alarm voice. Within 1 minute, the alarm  
enters the next circle automatically.  
5. Specifications  
Item  
Value  
Transmission Frequency  
Transmission Power  
ISM 2,400~2,483 MHz  
10mW/CE; 2mW/FCC  
2414MHz;2432MHz;2450MHz;2468MHz  
100m (328ft)(Min.)  
Operating Frequency  
Unobstructed Effective Range  
Modulation Mode  
GENERAL  
FM  
Operating Temperature  
Operating Humidity  
-10 ~ +50(Degree C) / +14~ +122(Degree F)  
≤85%RH  
 
Imaging Sensor Type  
Picture Total Pixels  
CMOS  
PAL:720×480 Pixels;  
NTSC: 720×576 Pixels  
Horizontal Resolution  
View Angle  
380 TV Lines  
PAL:55°; NTSC:55°  
Minimum Illumination  
BandWidth  
0Lux  
18M  
Night Vision Range  
Battery Working Time  
Motion Detection Distance  
Sound Control Sensitivity  
Consumption Current  
Power Supply  
5m  
CAMERA  
5 hours (IR OFF)  
5m (16ft)  
>63dB  
120mA(IR OFF)(Max.) & 220mA(IR ON)(Max.)  
DC +8V  
Dimensions(W×D×H)  
Weight  
86*48*135 mm (3.5*2*5.5 in)  
146 g (5.2 oz)  
2.4 inches TFT-LCD  
480×240  
LCD Screen Type  
Effective Pixels  
Receiving Sensitivity  
Video System  
≤-85dBm  
NTSC/PAL  
Battery Working Time  
Color Configuration  
Consumption Current  
Power Supply  
5 hours  
RECEIVER  
R.G.B.delta  
200mA(Max.)  
DC +8V  
Dimensions(W×D×H)  
Weight  
86*54*143 mm (3.5*2.25*5.75 in)  
142 g (5 oz)  
 
* Actual transmission range may vary according to weather, Location,  
interference and building construction.  
* All the specifications are subject to minor change without prior notice.  
6. FCC information  
This device complies with part 15 of the FCC Rules. Operation is subject to  
the following two conditions:  
(1) This device may not cause harmful interference.  
(2) This device must accept any interference received, including interference  
that may cause undesired operation.  
Changes or modifications not expressly approved by the party responsible  
for compliance could void the user’s authority to operate the equipment.  
CAUTIONS:  
Do not expose the device to water or other liquids.  
Turn off the Camera/Receiver when the system is not in use.  
Make sure the power adapter is easily accessible.  
Only remove the Camera/Receiver from the main power line by  
unplugging the adapter.  
Do not cut the DC power cable of the device to fit with another power  
source.  
Make sure batteries are disposed of properly.  
 
EU Environmental Protection  
Electrical waste products (discharged batteries) should not  
be disposed of with household waste.  
Please recycle where facilities exist.  
Check with your Local Authority or  
retailer for recycling advice.  
TRADEMARKS  
All brand names and products are registered trademarks of their respective  
Companies.  
DISCLAIMER  
The information in this document is subject to change without notice. The  
manufacturer makes no representations or warranties with respect to the contents  
hereof and specifically disclaim any implied warranties of selling or  
functionality for any particular purpose.  
 
LEGAL DISCLAIMER  
Warning: Your security camera is a quality digital product.  
You have to take utmost care while handling this product  
in order to ensure its reliability & durability.  
Digital Peripheral Solutions Inc.  
8015 E Crystal Drive.  
Anaheim, CA 92807,  
1-877-998-3440.  
Q-See Tech Support in U.S.A.  
Mon-Fri: 9 am 5 pm PST.  
TEL:1-877-998-3440  
 

RCA CRT Television 27F634T User Guide
Reebok Fitness Treadmill RBTL18921 User Guide
Remington Hair Dryer DS 1000 User Guide
ResMed Sleep Apnea Machine S8 AUTOSETTM II User Guide
Rio Audio MP3 Player SE510 User Guide
Roland Electronic Keyboard DP 990R User Guide
Samsung DVD Player DVD 1010 User Guide
Samsung DVD Player DVD E237 User Guide
Samsung Home Theater System HT DS140 User Guide
SATO Printer M10e Series User Guide