Renesas Network Card PCA7441 User Guide

PCA7441  
PCA7442FPG02  
PCA7442SP  
PROM Programming Adapters for 4513, 4514, 4518, 4519, 4583 and 4584 Groups  
User's Manual  
Rev.1.00  
July 1, 2003  
REJ10J0188-0100Z  
 
Contents  
Chapter 1. Precautions for Safety ...........................................................................................4  
Chapter 2. Introduction...........................................................................................................6  
2.1 Things to Check When Unpacking .......................................................................7  
Chapter 3. How to Write Programs ........................................................................................8  
3.1 Programming Procedures ......................................................................................8  
3.2 Attaching the Adapter to a PROM Programmer ...................................................9  
3.3 Inserting an MCU into the Adapter.......................................................................9  
(1) For PCA7441 .............................................................................................9  
(2) For PCA7442FPG02 ................................................................................10  
(3) For PCA7442SP .......................................................................................10  
3.4 Recommended PROM Programmers ..................................................................12  
Chapter 4. Specifications ......................................................................................................13  
4.1 Specifications ......................................................................................................13  
4.2 Memory Maps .....................................................................................................14  
Chapter 5. Troubleshooting ..................................................................................................15  
5.1 Errors That Occur When Writing to PROM .......................................................15  
(1) When Newly Purchased ...........................................................................15  
(2) Previously Written Normally ...................................................................15  
5.2 MCUs Do Not Function Normally......................................................................15  
5.3 Other Precautions ................................................................................................16  
(1) About the Recommended PROM Programmers ......................................16  
(2) About Reading Out of Device Identification Code ..................................16  
5.4 How to Request for Support................................................................................16  
( 3 / 18 )  
 
Chapter 1. Precautions for Safety  
In both the user's manual and on the product itself, several icons are used to insure proper handling  
of this product and also to prevent injuries to you or other persons, or damage to your properties.  
This chapter describes the precautions which should be taken in order to use this product safely and  
properly. Be sure to read this chapter before using this product.  
If the requirements shown in the "WARNING"  
sentences are ignored, the equipment may  
cause serious personal injury or death.  
WARNING  
If the requirements shown in the "CAUTION"  
sentences are ignored, the equipment may  
malfunction.  
CAUTION  
It means important information on using this  
IMPORTANT  
product.  
In addition to the three above, the following are also used as appropriate.  
means WARNING or CAUTION.  
Example:  
CAUTION AGAINST AN ELECTRIC SHOCK  
means PROHIBITION.  
Example:  
DISASSEMBLY PROHIBITED  
means A FORCIBLE ACTION.  
Example:  
UNPLUG THE POWER CABLE FROM THE RECEPTACLE.  
The following pages describe the symbols "WARNING", "CAUTION", and "IMPORTANT".  
( 4 / 18 )  
 
WARNING  
Warnings for Use Environment:  
• This equipment is to be used in an environment with a maximum ambient temperature of 35˚C. Care  
should be taken that this temperature is not exceeded.  
• Select the proper programming mode of the PROM programmer.  
CAUTION  
Caution to Be Taken for Modifying This Product:  
• Do not disassemble or modify this product. Disassembling or modifying this product can cause  
damage. Disassembling and modifying the product will void your warranty.  
Cautions to Be Taken for This Product:  
• Use caution when handling this product. Be careful not to apply a mechanical shock such as falling.  
• Do not directly touch the connector pins of this product.  
• Be careful with the static electricity when handling this product and the MCU.  
Caution for Keeping This Product:  
• When not using this product for a long time:  
(1) Attach the connector pins of this product to the conductive sponge.  
(2) Put it into a conductive polyvinyl, and keep it in the package case shipped from the factory.  
(3) Store it in the place where humidity and temperature are low and direct sunshine does not  
strike.  
IMPORTANT  
Note on This Product:  
• We cannot accept any request for repair.  
When Using This Product:  
• Attach this product to the IC socket on the PROM programmer properly.  
• Insert the MCU to the IC socket of this product properly.  
• When opening and closing the IC socket of this product, be sure to keep it horizontal.  
• Be sure to set the programming area as described in this user's manual.  
• Do not use the PROM programmer's device identification code readout function.  
( 5 / 18 )  
 
Chapter 2. Introduction  
This product is a PROM programming adapter for the 4513, 4514, 4518, 4519, 4583 and 4584 Groups  
of 4-bit MCUs. This product is used to write programs into the internal EPROM of MCU with  
commercially available PROM programmer. This manual mainly explains specifications of this  
product and how to operate it. Figures 2.1 to 2.3 show the external view of the products and their  
constituent parts.  
Figure 2.1 External view of the adapter and constituent parts (PCA7441)  
Figure 2.2 External view of the adapter and constituent parts (PCA7442FPG02)  
( 6 / 18 )  
 
Figure 2.3 External view of the adapter and constituent parts (PCA7442SP)  
2.1 Things to Check When Unpacking  
This product consists of the parts listed in Table 2.1. When unpacking, check to see that it contains  
all of the components.  
Table 2.1 Package components  
Main unit  
PCA7441/PCA7442FPG02/PCA7442SP  
PCA7414B  
Interface unit  
Connector  
PCA7402D (28-pin)  
This manual  
User's manual  
* If any part is missing or there is any doubt about your product package, contact your local  
distributor.  
( 7 / 18 )  
 
Chapter 3. How to Write Programs  
This chapter describes procedures you need to follow when writing the program.  
For details on how to operate the PROM programmer, refer to the user's manual of the PROM  
programmer.  
3.1 Programming Procedures  
Follow the steps (1) to (6) to write the program.  
(1) Read the program into the PROM programmer.  
(2) Attach the adapter to the PROM programmer. (see 3.2).  
(3) Insert the MCU into the adapter. (see 3.3)  
(4) Using the PROM programmer's erase check function, check whether data can be written into  
the MCU's programming area. *  
(5) Write the program into the programming area of the MCU using the PROM programmer. *  
(6) Verify the programming area of the MCU using the PROM programmer to check whether the  
program has been written into the MCU correctly. *  
Notes:  
*1 Be sure to set the programming area. Otherwise the mode's shift to the programming mode may  
not be performed successfully. The erase check function etc. may not also be performed  
completely.  
*2 Some PROM programmers perform the steps (4) through (6) automatically.  
( 8 / 18 )  
 
3.2 Attaching the Adapter to a PROM Programmer  
As shown in Figure 3.1, attach the No. 1 pin of the PCA7402D connector (standard-pitch 28-pin pin-  
header mounted) to the No. 1 pin of the IC socket of the PROM programmer.  
Be careful when attaching to the PROM programmer because an incorrect  
insertion can cause fatal damage to the MCU.  
Figure 3.1 Attaching the adapter to a PROM programmer  
3.3 Inserting an MCU into the Adapter  
(1) For PCA7441  
As shown in Figure 3.2, set the slide bar of the IC socket to the right side (marked on the board) and  
insert the MCU into the IC socket, with the pin No. 1 of the MCU matched to the pin No. 1 of the IC  
socket.  
Be careful when attaching to the PROM programmer because an incorrect  
insertion can cause fatal damage to the MCU.  
Top view  
Figure 3.2 Inserting an MCU (PCA7441)  
( 9 / 18 )  
 
(2) For PCA7442FPG02  
As shown in Figure 3.3, insert the MCU into the IC socket with the No. 1 pin of the MCU matched  
to the No. 1 pin of the IC socket on the PCA7442FPG02.  
Be careful when attaching to the PROM programmer because an incorrect  
insertion can cause fatal damage to the MCU.  
Top view  
Figure 3.3 Inserting an MCU (PCA7442FPG02)  
(3) For PCA7442SP  
As shown in Figure 3.4, insert the MCU into the IC socket with the No. 1 pin of the MCU matched  
to the No. 1 pin of the IC socket on the PCA7442SP.  
Be careful when attaching to the PROM programmer because an incorrect  
insertion can cause fatal damage to the MCU.  
Top view  
Figure 3.4 Inserting an MCU (PCA7442SP)  
( 10 / 18 )  
 
CAUTION  
Cuation for the Slide Bar of the PCA7441:  
• There is a slide bar in the center of the PCA7441. Set this slide bar to the shaded area  
(factory-setting). Otherwise the MCU may cause a break because of an electrical  
insulation failure.  
Caution to Be Taken for Handling an MCU:  
• Do not touch the connector in the IC socket and the pins on the PROM programmer  
connector. Otherwise it can cause an electrical insulation failure because of dirt.  
When not using, attach the connector pins of this product to the conductive sponge  
as it was shipped from the factory.  
Caution When Opening and Closing the IC Socket:  
• When opening and closing the IC socket, hold the adapter horizontally as shown in  
Figure 3.5. Otherwise the inside of the IC socket may become damaged and cause  
an electrical insulation failure.  
Side view  
Figure 3.5 Opening and closing the IC socket  
( 11 / 18 )  
 
3.4 Recommended PROM Programmers  
The PROM programmers listed in Table 3.1 are recommended for this product. Using the actual  
products, we have verified that these PROM programmers can be used to write programs without  
problem. Nonconformity occurring by using any other PROM programmers listed in Table 3.1 can  
not be supported. For how to operate the PROM programmer and the latest type of PROM  
programmers, contact the manufacturer to confirm whether it can be used for your product.  
Table 3.1 Recommended PROM programmers  
Manufacturer  
Type name  
TR4943  
R4944A  
R4945  
Device  
Programming voltage (Vpp)  
M5L27256 mode  
M5L27C256 mode  
M5M27C256A mode  
M5M27C256A mode  
Advantest Corporation  
12.5 V  
R4945A  
( 12 / 18 )  
 
Chapter 4. Specifications  
4.1 Specifications  
Table 4.1 lists common specifications of the programming adapters, and Table 4.2 lists individual  
specifications of each programming adapter.  
Table 4.1 Common specifications of the PCA7441, PCA7442FPG02 and PCA7442SP  
1.0 MHz  
Operating clock frequency  
(Supplied by the ceramic oscillator mounted on the adapter)  
Power supply  
Main unit  
Supplied from Vcc of the PROM programmer  
Board to insert a programmable MCU  
(IC socket for MCU mounted)  
Interface board  
Board  
configuration  
PCA7414B  
(Interface unit)  
(Connected by two rows of standard-pitch 18-pin connectors  
and two rows of standard-pitch 16-pin connectors to the upper  
and lower boards)  
Board to connect to the PROM programmer  
(Standard-pitch 28-pin pin-header mounted)  
PCA7402D  
(Connector)  
Table 4.2 Specifications of each adapter  
Product name  
Item  
Description  
4500 Series 42-pin 0.8-mm-pitch SSOP (42P2R-A)  
M34514E8FP, M34519E8FP, M34574EDFP  
MCU  
PCA7441  
IC51-0422-393 (made by Yamaichi Electronics Co. Ltd.)  
IC socket  
4500 Series 32-pin 0.8-mm-pitch LQFP (32P6B-A, 32P6U-A)  
M34513E4/E8FP, M34518E8FP, M34583EDFP  
MCU  
IC socket  
MCU  
PCA7442FPG02  
PCA7442SP  
IC51-1498.AC-26323 (made by Yamaichi Electronics Co. Ltd.)  
4500 Series 32-pin 1.778-mm-pitch SDIP (32P4B)  
M34513E4/E8SP, M34518E8SP  
IC59-3204-G4 (made by Yamaichi Electronics Co. Ltd.)  
IC socket  
( 13 / 18 )  
 
4.2 Memory Maps  
Figure 4.1 shows memory maps of the MCU and the PROM programmer.  
PROM programmer  
MCU  
0000h  
XXXXh  
0000h  
XXXXh  
Programming area*3  
(10 bits x ZZZZZ words)  
*1  
*1  
Lower 5 bits  
*2  
Unused area*4  
3FFFh  
3FFFh  
4000h  
Upper 5 bits  
YYYYh  
*2  
7FFFh  
*1: This area is fixed to "1" on the PROM programmer.  
*2: Set "FFh".  
*3: When writing, the lower 5 bits and the upper 5 bits are divided and then written into  
the MCU.  
*4: When reading, "1" is read out.  
ROM capacity  
ZZZZZ  
4,096  
XXXX  
0FFF  
1FFF  
3FFF  
YYYY  
4FFF  
5FFF  
7FFF  
E4  
E8  
ED  
8,192  
16,384  
Figure 4.1 Memory maps  
( 14 / 18 )  
 
Chapter 5. Troubleshooting  
The table below summarizes errors to be checked carefully before you determine them to be a fault.  
5.1 Errors That Occur When Writing to PROM  
(1) When Newly Purchased  
Remedy  
Cause  
See page  
9
Is the adapter attached to the correct position of the PROM  
programmer?  
Programming adapter  
Is the MCU attached to the correct position?  
Is the correct device selected?  
9
PROM programmer  
Contact failure  
12  
The IC socket of the PROM programmer may be stained. The  
socket needs replacing.  
-
(2) Previously Written Normally  
Remedy  
Cause  
See page  
9
Is the adapter attached to the correct position of the PROM  
programmer?  
Programming adapter  
PROM programmer  
Is the MCU attached to the correct position?  
Is the correct device selected?  
9
12  
The IC socket of the PROM programmer may be stained. The  
socket needs replacing.  
-
-
Contact failure  
The PROM programmer connector (28-pin pin-header) at which  
the PROM programmer is contacted may be stained. Clean it  
with alcohol, etc.  
5.2 MCUs Do Not Function Normally  
The program operates normally on the emulator, but when the MCU that has normally been written  
is attached the same program does not function normally.  
(1) In the emulator, NOPs are often inserted in the area where the program has not been read, therefore  
the program happens to appear functioning normally even though it may have gone wild. Check  
your program again.  
(2) The emulator and the actual MCU may differ in characteristics. Consult the user's manual of the  
emulation pod to check for differences in characteristics again.  
( 15 / 18 )  
 
5.3 Other Precautions  
(1) About the Recommended PROM Programmers  
Not all PROM programmers available on the market can be checked to see if they function properly.  
There are several PROM programmers that we have verified to function properly. These products are  
listed as recommended PROM programmers in this user's manual. Other PROM programmers may  
also be used providing that you verified them to function properly.  
Note: No matter which type of PROM programmer you use, it is necessary to verify completion of  
programming by executing screening, etc. that are stipulated for each MCU used.  
(2) About Reading Out of Device Identification Code *1  
Please do not use the PROM programmer's device identification code readout function.  
Using this function may break down the MCU. The device identification code is included in EPROM  
to indicate the manufacturer code and device code; it is not included in the MCU.  
*1 Depending on PROM programmer manufacturers, this may be referred to by another name (e.g.  
ID code).  
5.4 How to Request for Support  
After checking this manual, fill in the following information and email to your local distributor.  
For prompt response, please specify the following information:  
(1) Contact address  
• Company name  
• Department  
• Responsible person  
• Phone number  
• Fax number  
• E-mail address  
(2) Product information  
• Name of the programming adapter  
• Serial number  
• Date of purchase  
• Target MCU  
• Symptoms (Fails blank check/Cannot write a program/Fails verification etc.)  
• Detailed symptoms  
• How often does the problem occur? (2 out of 10 etc.)  
• When did the problem start to occur? (Since purchase/Used to work correctly)  
• Type name of the PROM programmer (Advantest R4945A etc.)  
• Specified device when writing to PROM (M27C101 etc.)  
• Specified programming area when writing to PROM  
• Switch settings of the adapter when writing to PROM  
( 16 / 18 )  
 
PCA7441, PCA7442FPG02, PCA7442SP User's Manual  
Rev.1.00  
July 1, 2003  
REJ10J0188-0100Z  
COPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATION  
AND RENESAS SOLUTIONS CORPORATION ALL RIGHTS RESERVED  
 
 

Quantum Wheelchair 06 edge va User Guide
Raymarine Fish Finder C140w User Guide
RCA VCR VR708HF User Guide
Rhino Mounts Chipper TW144 User Guide
Ricoh Photo Scanner IS450 User Guide
RIDGID Pressure Washer RD80763 User Guide
Roberts Radio Clock Radio CR9955 User Guide
Rosen Entertainment Systems GPS Receiver DS MZ0830 User Guide
Samsung Computer Monitor 20081006091108750 User Guide
Sceptre Technologies Flat Panel Television X42 User Guide