Seagate BARRACUDA ST320011A User Manual

Master or single drive: To configure the drive as a master or a single  
drive, set the jumper on pins 7 and 8.  
Drive is slave: To configure the drive as a slave, or second drive on  
®
Barracuda ATA IV Family Installation Guide  
the cable, remove all the jumpers.  
ST380021A, ST360021A, ST340016A, ST320011A  
Master with non ATA-compatible slave: Use this setting if the slave  
drive is not recognized. Configure the master drive with a jumper set on  
pins 5 and 6 and pins 7 and 8 to enable this option.  
Publication number:100129216, Rev.A  
The Easiest Way to Install Your Drive  
Cable select option: Cable Select jumpers use the cable to determine  
master or slave. To enable cable select, set a jumper on pins 5 and 6. If  
using two drives, jumpers for both drives should be set on pins 5 and 6.  
DiscWizard is Seagate’s exclusive Windows program that is included with  
your drive for easy drive installation. You can use this software if you have a  
bootable hard drive in your computer and are running Windows Me,  
Windows 98 or Windows 95. Download the software from our Web site at  
Alternate capacity jumper: Drives with a 40-Gbyte capacity and  
greater are limited to 32 Gbytes. This jumper is used to provide a  
solution to specific legacy BIOS problems. When using the alternate  
capacity jumper, Disk Manager software is required to achieve the  
drive’s full capacity.  
.
Run DiscWizard before installing your drive for customized step-by-step  
instructions for your system.  
Attaching Cables and Mounting the Drive  
To run DiscWizard:  
instructions to complete the installation.  
If you cannot run DiscWizard, follow the instructions on this installation  
sheet to install and configure your drive.  
1. Attach one end of the drive interface cable to the interface connector  
on your computer’s motherboard (see your computer manual for  
connector locations).  
Caution. Align pin 1 on the motherboard connector with pin 1 on  
your drive connector. Pin 1 is marked by a stripe on one side of the cable.  
!
What You Need  
A Phillips screwdriver and four 6-32 UNC drive mounting screws  
2. Attach the interface connector and the power connector to the drive.  
Note. You can mount the drive in any orientation. Usually it is mounted  
A standard 40-pin ATA interface cable, or an 80-conductor cable to run  
with the circuit board down.  
Ultra ATA 100 (max length: 18 inches)  
3. Secure the drive in the computer using four 6-32 UNC mounting  
screws in either the side-mounting or bottom-mounting holes. Insert  
the screws no more than 0.20 inch (5.08 mm) into the bottom-mounting  
holes and no more than 0.14 inch (3.55 mm) into the side-mounting holes.  
An unused drive power cable for your new drive  
A version of Windows with FAT32 file system for drives over 32 Gbytes  
Ultra ATA/100 Requirements  
Note. When configuring two ATA devices on  
The drive can be configured to support a default maximum transfer rate.  
This drive can support transfer rates up to 100 Mbytes per second  
(UDMA 5) in Ultra ATA/100 mode. Using a software utility, you can set the  
default transfer rate to the best capability of your system. For your drive to  
run in this mode, you need the following:  
the same cable, both must use Cable  
Select or both must use Master/Slave  
Master  
Pin 1  
jumper settings. If using a standard  
40-pin cable, the master and slave  
drives can be placed in any position. If  
using a 40-pin 80-conductor cable, attach  
the blue connector to the motherboard,  
the black connector to the master drive  
and the grey connector to the slave.  
Computer  
Motherboard  
Slave  
A computer that supports UDMA mode 5  
A 40-pin 80-conductor cable (available from your dealer)  
Caution. Do not overtighten the screws or use metric screws. This  
A software utility to confirm and activate Ultra ATA/100. Seagate® provides  
a utility called UATA100.exe. You can download the latest version from our  
!
may damage the drive.  
Windows Me or Windows 98 operating system: either supports Ultra  
Power  
connector  
ATA\100.  
Handling Precautions  
Disc drives are extremely fragile. Do not drop or jar the drive.  
Interface  
connector  
Pin 1  
Keep the drive in the protective SeaShell container until you are  
ready to install it. This minimizes handling damage.  
The drive has a protective cover called SeaShield®. Do not remove  
this permanent cover—it protects the drive from electrostatic  
discharge (ESD) and minor impact damage.  
Configuring the BIOS  
For your computer to recognize your new drive, configure your  
computer’s BIOS as follows:  
Protect your drive from static discharge by wearing a grounded wrist  
strap throughout the installation process.  
1. Run the system setup program.  
Always handle the drive by the edges or frame.  
2. Enable LBA mode and UDMA mode, if available.  
Do not apply pressure or attach labels to the circuit board or the  
top of the drive.  
3. Select the auto-detect option. If necessary, refer to the drive param  
eters on your drive label to configure the drive for your system. BIOS  
capacity of the drive, use LBA mode or use Disk Manager.  
Setting the Jumpers  
Options jumper block  
Refer to the jumper settings  
4. Save and exit the system setup program.  
*Master or single drive  
on your drive label to  
configure the drive for your  
system. Jumper settings also  
can be accessed online from  
our Web site at  
BIOS Settings  
Drive is slave  
Master with non ATA-  
compatible slave  
Drive Model  
ST380021A  
ST360021A  
ST340016A  
ST320011A  
Formatted Gbytes  
Total Sectors*  
156,301,488  
117,231,408  
78,165,360  
80.0  
60.0  
40.0  
20.0  
*Cable select  
Limit drive capacity  
>32 Gbytes = 32 Gbytes  
<32 Gbytes = 2.1 Gbytes  
39,102,336  
7
8
5
6
3
4
1
2
*Drives may be shipped with  
either configuration as default.  
Circuit Board  
*One sector equals 512 bytes.  

Transcend Information TS64MMSC User Manual
Toro V100 User Manual
Sony RCD W100 User Manual
Sonic Impact Technologies SFT 1 User Manual
Sherwood V 903 User Manual
Samsung SGH U600 User Manual
Samsung SGH T409 User Manual
Raritan Computer Computer Accessories DCIM PS2 User Manual
Pioneer DEH P4850MP User Manual
Nokia 6590i User Manual